LUMI LIGHT INSTRUCTIONS

Turn On

Double Tap or Hold (1 Sec)

Check Battery

Tap when off

Green=70%+ Yellow=30%+ Red=30%-

Next Mode

Tap

Previous Mode

Double Tap

Turn Off

Hold

Brightness Control

Four taps (from off)

Cycle through the four brightness levels. The default level is Level 3. Max is Level 4.
Single Click to cycle,
Long Press to save.

Start-up Mode

Five Taps (from off)

Choose between starting from your last used mode or resetting to the first mode upon power-up.
Green Flash = Start on Last Used
Orange Flash = Start from Mode 1

Flow Mode

Six taps (from off)

Toggle between Juggle (Slower) and Spin (Faster) mode groups to instantly change the speed and style of your light patterns.
Pink Flash = Juggle Mode
Blue Flash = Spin Modes.

24 ADVANCED COLOUR MODES

METEORS - STROBES - RAINBOWS - SOLIDS

SPIN - Fast Mode

Optimized for high-speed movement. This mode ensures patterns remain crisp and vibrant during fast spins and rapid transitions.

JUGGLE - Slow Mode

Optimized for technical, rhythmic movement. This mode enhances pattern detail and trail visibility when the prop is moving at a slower, controlled pace.

Charging Cable / Power Warning!

Charging Cable included. Power adapter not included. Use only a standard USB power adapter: 5V, up to 2A (10W max). Regular phone chargers (5V 1A or 2A) are safe. Do not use fast-charge or high-voltage adapters (9V, 12V, 20V) - this may overheat the cable, damage the poi, or cause a fire hazard.

LIGHT UNIT SPECIFICATIONS

Voltage = 3.7 V 

Charging Port = USB-C

 Battery Life = 16 hrs (depending on the mode) 

Charging Time = +/- 2 hrs

 

CORD LENGTH ADJUSTMENT

Non-Lit Handle

  1. Use a butter knife to remove the white plastic knob insert.
  2. Pull the rope and washers out of the knob.
  3. Mark the desired new length and place the washers behind the mark, leaving a small gap.
  4. Wrap a small piece of sticky tape next to the mark.
  5. Cut the rope with scissors or a Stanley knife.
  6. Melt the rope end with a lighter.
  7. Remove the tape and slide the washers against the melted end.
  8. Slide the knob onto the rope and reinstall the white plastic insert.

LED Handle

  1. Squeeze the silicone knob to push the light unit out.
  2. Squeeze the knob again to remove the inner ring and rope end.
  3. Mark the desired new length and wrap a small piece of sticky tape next to the mark.
  4. Cut the rope with scissors or a Stanley knife.
  5. Melt the rope end with a lighter. Make sure the melted end is small enough to fit into the ring recess.
  6. Remove the tape and slide the ring onto the rope, against the melted end.
  7. Pull the rope to position the ring inside the knob.
  8. Push the light unit fully back into the silicone knob.

 

CORD replacement

  1. Squeeze the silicone ball near the rope. The light unit will come out from the opposite end.

  2. Once the securing ring is visible, pull the light unit and rope out.

  3. Use a small Phillips screwdriver to remove the screw securing the ring to the light unit.

  4. Slide the ring and plastic washer off the light unit and leave them on the rope.

  5. Use a butter knife to carefully separate the two halves of the light unit.

  6. Remove the old rope from the slot and pull it completely out of the silicone ball.

  7. Insert the new rope through the silicone ball and slide the securing ring  and the plastic washer onto the rope.

  8. Place the rope end into the slot in the light unit and close the two halves together.

  9. Slide the plastic washer and securing ring back onto the light unit.

  10. Reinstall the screw to secure the ring in the same position.

  11. Pull the rope from the opposite side of the ball to fully insert the light unit.

  12. Make sure the plastic washer sits correctly in the silicone ball slot, against the light unit head.

Time to play!